Toilet rocks and leaks at the base
We pull the toilet, inspect the flange, replace the wax ring, and reset the bowl level with shims. If the flange is broken, we cut it out and install a new one. The rocking stops and the base stays dry.
Same-day installs, code-correct work, old toilet hauled away
Toilet Replacement Phoenix AZ Done Right the First Time
Toilet Replacement Phoenix AZ homeowners can count on starts with a straight answer and a fair price. Whether your old bowl is cracked, rocking on a failed wax ring, or just guzzling water at 3.5 gallons a flush, we pull it, set the new one level, and test every cycle before we leave. We serve Maricopa County seven days a week, including same-day toilet swap Phoenix appointments when the schedule allows.
Careful work. Honest options.
About this service
What Toilet Replacement Phoenix AZ Really Involves
Toilet Replacement Phoenix AZ is the full removal and reinstallation of a toilet, including shutting off the supply, pulling the old fixture, inspecting the flange, setting a new wax ring, and bolting down a new bowl and tank. It is not a repair. We are swapping the whole unit because the porcelain, the flush valve, or the floor connection has failed past the point where parts alone fix it. Most jobs run two to four hours, and we handle the haul-away so you are not stuck with a cracked bowl in your alley.
Phoenix homes built before 1994 often still have 3.5-gallon toilets that waste water and short-flush in hard water. Our water here runs 8 to 12 grains per gallon, which eats rubber flappers and fill valves fast. If you are searching for a toilet swap near me Phoenix because the tank keeps running or the base rocks, that is usually a wax ring or flange problem, not just a worn flapper. We see it in Roosevelt Row bungalows and Ahwatukee two-stories alike. Replacing the unit solves the leak and the water bill in one visit.
- ✓ Lower Water Bills
- ✓ No More Rocking
- ✓ Strong, Quiet Flush
- ✓ Code-Correct Install
What's included
What Is Included in Toilet Replacement
Every toilet replacement Phoenix AZ job includes the full removal and install, not just the parts. We handle the old unit, the wax ring, the supply line, and the final test. If we find a broken flange or a bad shut-off valve during the job, we show you and quote the fix before we proceed.
✓
Old Toilet Removal
We shut off the water, drain the tank, disconnect the supply, and pull the old toilet. The wax ring and bolts get bagged, and the unit goes on the truck. No mess left in the bathroom, no toilet on your curb.
✓
Flange Inspection
We check the toilet flange for cracks, rust, and proper height. A broken flange is the number one cause of a rocking toilet and a repeat leak. If it is damaged, we quote the repair before we set the new toilet.
✓
New Wax Ring and Bolts
A fresh wax ring goes down centered on the flange, and new closet bolts hold the bowl. We do not reuse old rings or bolts. This is the seal that keeps water and sewer gas where they belong.
✓
Supply Line and Valve Check
We inspect the shut-off valve and supply line. If the valve is stuck or the line is brittle, we replace them with a quarter-turn ball valve and a braided stainless supply. Small parts, big flood prevention.
✓
Set, Level, and Caulk
The new toilet is set level, shimmed at the base, and bolted snug. We caulk the base with mold-resistant silicone and leave a gap at the back so a future leak is visible. Clean, code-correct finish.
✓
Flush Test and Walkthrough
We flush the toilet five times and check for leaks at the tank, base, and supply. Then we walk you through the install, show you the shut-off valve, and explain the workmanship warranty. You know how it works before we leave.
How it works
How Our Toilet Replacement Process Works
01
Phone Triage
You call or text and describe the problem: leaking, rocking, running, cracked tank, or a full remodel. We ask the age of the toilet and whether the shut-off valve turns. That tells us if this is a straightforward swap or a flange repair. We quote a range on the call and book a window, often same day.
02
On-Site Inspection
We pull the lid, check the flapper and fill valve, and look for water staining around the base. A toilet auger or inspection camera goes in if there is a clog concern. We measure the rough-in from the finished wall to the closet bolts. Ten minutes, and we know exactly what the job needs.
03
Shut-Off and Removal
We close the shut-off valve, drain the tank, and disconnect the supply line. The old toilet comes up with a putty knife under the caulk line and an adjustable wrench on the closet bolts. We bag the wax ring and haul the unit out to the truck. Floor gets wiped and checked for soft spots.
04
Flange and Ring Prep
This is where cheap installs fail. We inspect the toilet flange for cracks and rust. If it is broken, we cut it out and set a new one. Then a fresh wax ring goes down, centered on the flange. A new supply line and, if needed, a new shut-off valve go in before the new bowl lands.
05
Set, Seal, and Test
The new toilet gets set level, shimmed at the base, and bolted down snug, not cranked. We reconnect the supply, open the valve, and flush five times. We check for leaks at the tank, the base, and the supply line. Then we caulk the base, clean up, and walk you through the warranty.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Toilet auger
Clears clogs in the trap without scratching the porcelain. We use a professional auger with a protective sleeve, then flush-test to confirm the line is open.
Plumber's snake
Reaches deeper clogs past the toilet trap and into the drain line. Used when an auger is not enough or when the clog keeps returning.
Inspection camera
Shows the inside of the drain and flange. We use it when clogs repeat or when a toilet replacement reveals a suspect drain or broken flange.
Adjustable wrench and putty knife
Pull the closet bolts and cut the old caulk line. Basic tools, but the right ones prevent chipped porcelain and scratched floors.
Wax ring and flange bolts
The seal and the hardware that hold the toilet to the floor. We use new rings and bolts on every install, never reused parts.
Fluidmaster and Korky valves
Fill valves and flappers that hold up to Phoenix hard water. We stock both brands on the truck so the install is done in one visit.
Sloan and Danco parts
Flush valves, gaskets, and seals for commercial and residential fixtures. Used when a repair is the right call instead of a full replacement.
Real results
Before and after.
Rocking Toilet to Solid Install
Before
A 1998 American Standard in a Coronado home rocked every time someone sat down. The wax ring was crushed, the flange was cracked, and there was a faint sewer smell. The homeowner had been ignoring it for a year.
After
We cut out the broken flange, installed a new one, set a new Kohler with a fresh wax ring, and shimmed the base level. The toilet does not move, the smell is gone, and the floor is dry. Job took three hours.
Running Toilet to Water Saver
Before
A 3.5-gallon toilet in Maryvale ran constantly. The flapper was warped from hard water, and the fill valve was noisy. The water bill had climbed $60 a month. The homeowner wanted a fix, not a patch.
After
We replaced the toilet with a 1.28-gallon EPA WaterSense model, installed a new Fluidmaster fill valve, and tested the flush five times. Water use dropped by 60 percent. The running noise stopped the same day.
Cracked Tank to Same-Day Swap
Before
A homeowner in Arcadia woke up to water on the bathroom floor. The tank had a hairline crack that finally failed. The shut-off valve was stuck, so they could not stop the water. They called us at 7 a.m.
After
We shut off the main, replaced the stuck valve with a quarter-turn ball valve, pulled the cracked toilet, and installed a new Toto with a soft-close seat. Done by 1 p.m. the same day. No floor damage.
Problems we solve
Toilet Problems We Solve in Phoenix
Most toilet calls come down to five failures. Here is what we see, what happens if you wait, and how we fix it.
Ask a pro →↗
Running toilet that will not stop
We replace the flapper, fill valve, or flush valve with Fluidmaster or Korky parts. If the porcelain is cracked or the valve seat is damaged, we quote a full replacement. Most running toilets are fixed in under an hour.
Weak flush and repeat clogs
We run a toilet auger first, then a camera inspection if the clog returns. If the trap or flush valve is the problem, a new 1.28-gallon EPA WaterSense toilet solves it. You get a strong flush and lower water use.
Cracked tank or bowl
We replace the toilet. Patching a cracked tank with epoxy is a temporary fix at best. We pull the old unit, set a new Kohler or American Standard, and haul the cracked one away the same visit.
Proof you can check
Licensed, Insured, and Reviewed
✓
Arizona Registrar of Contractors (ROC) licenseArizona Registrar of Contractors
✓
EPA WaterSense partnerU.S. Environmental Protection Agency
✓
OSHA safety complianceOccupational Safety and Health Administration
✓
Uniform Plumbing Code (UPC) certified installsInternational Association of Plumbing and Mechanical Officials
✓
ASSE 1002 fill valve standardAmerican Society of Sanitary Engineering
Most toilet replacement jobs in Phoenix run $250 to $650 for labor and disposal, plus the cost of the toilet itself, which ranges from $150 for a basic model to $1,200 or more for a smart toilet. A broken flange or corroded shut-off valve adds $75 to $200. We quote the full job before we start.
Yes, in most cases. If you call before noon, we can usually have a same-day toilet replacement Phoenix appointment on the schedule. We stock common rough-in sizes and wax rings on the truck, so we are not waiting on a supply house. Weekend and evening slots are available for emergencies.
Our toilet replacement Phoenix service includes pulling the old toilet, inspecting the flange, installing a new wax ring, setting and leveling the new bowl, connecting a new supply line, testing for leaks, caulking the base, and hauling the old unit away. Toilet and any flange repair are quoted separately and approved before work begins.
Yes. Every toilet replacement and disposal Phoenix job includes haul-away. We carry the old toilet out, bag the wax ring and bolts, and dispose of the unit properly. You do not need to schedule a bulk pickup or leave it in the alley. The floor gets wiped down before we leave.
More services
Related Toilet Services We Offer
Toilet InstallationNew construction or remodel installs where there was no toilet before. We set the flange, rough-in, supply, and drain line to code. If you are replacing a toilet during a bathroom remodel in Phoenix, we coordinate with your tile and flooring schedule.Explore →
Running Toilet RepairA running toilet can waste 200 gallons a day. We replace the flapper, fill valve, or flush valve with Fluidmaster or Korky parts. If the tank is cracked or the porcelain is worn, replacement is often the smarter spend than repeated repairs.Explore →
Leaking Toilet RepairLeaks at the base, tank, or supply line. We trace the source with an inspection camera if needed, replace the wax ring or tank gasket, and test under pressure. Catching a base leak early prevents subfloor rot and a much bigger bill.Explore →
Clogged Toilet RepairWe clear clogs with a toilet auger first, then a plumber's snake if the blockage is deeper. If the clog keeps returning, a camera inspection finds the real cause. Sometimes a failing toilet is the root of repeat clogs, and replacement is the fix.Explore →Toilet Tank RepairCracks, leaks at the tank bolts, or a failed flush valve. We replace tank-to-bowl gaskets, bolts, and internal valves. If the tank porcelain is cracked, a full toilet replacement Phoenix AZ install is usually the safer call than a patch.Explore →
Toilet Bowl RepairChips, cracks, and hairline fractures in the bowl. A cracked bowl can fail without warning and flood the floor. We assess whether the bowl can be sealed or the whole unit needs replacing. Most cracked bowls mean it is time for a new toilet.Explore →
Toilet Flush Valve RepairThe flush valve controls how much water leaves the tank. A worn seal causes a weak flush or a constant run. We replace the flush valve and seal, then test the flush cycle. If the valve seat is damaged, replacement may be the better option.Explore →
Toilet Fill Valve RepairThe fill valve refills the tank after each flush. A failing valve causes noise, slow refill, or overflow. We install Fluidmaster or Korky fill valves, set the water level correctly, and check for leaks at the shank. Quick job, big difference in water use.Explore → Ready when you are
Ready for Toilet Replacement Phoenix AZ? Call Today
One call gets you a straight price, a same-day window, and a licensed plumber who hauls the old toilet away. We answer the phone 24/7 for emergencies. Call now and we will tell you exactly when we can be there.
Book My Install +16028350160 →
Request an appointment
Contact Phoenix Toilet Repair Co
Call us at +1 (602) 835-0160 or email info@phoenixtoiletrepairco.com. We answer 24/7 for emergencies and schedule same-day appointments for standard repairs. If you leave a message after hours, we call back first thing in the morning. Most jobs get a plumber to your door the same day.
Call anytime+16028350160Email the officeinfo@toiletrepairphoenixaz.pages.dev
Office hoursOpen 24 hours · 7 days a week